top of page

CONCRETE COOPRESSIVE STRENGHT CHARACTERISTIC

 

CONCRETE COMPRESSIVE STRENGTH CHARACTERISTIC

Beton duvarda gölge

Axial Extensometer (Compressometer)

Axial extensometer is designed for the determination of the modulus of elasticity in compression of mortar, cement, concrete, rock and other materials.

1.jpg
Ayrıntılar
Beton duvarda gölge

Test Samples

Test specimens after testing still equipped with the extensometric cage. Laboratory tests are performed to evaluate the durability and performance of epoxy resins; often used to re-evaluate all or part of the epoxy resins after testing

3.jpg
Ayrıntılar
Beton duvarda gölge

Air Meter

Checking the air content of concrete elements with an air meter.

5.jpg
Ayrıntılar
Beton duvarda gölge

Compressive strength test

Compressive strength test on cube of concrete. A compression strength test is a mechanical test that measures the maximum compressive load that a material can withstand before cracking. Usually the test piece is in cube, prism or cylindrical form and is applied between the plates of a compression testing machine. 

Concrete's crushing strength, or cube strength, is about 3 tons per square inch, while granite is around 10 tons per square inch, and cast iron ranges from 25 to 60 tons per square inch.

7.jpg
Ayrıntılar
Beton duvarda gölge

Concrete pipe machine testing

Concrete pipe testing machines are equipped with a hydraulic power pack and a load cell. These machines have a frame consisting of two rigid columns and a carrier frame. The double-acting actuator in the upper beam is supported by an anti-rotation system to prevent rotation tendency.

9.jpg
Ayrıntılar
Beton duvarda gölge

Strength of concrete

The strength of concrete is the most important indicator that determines the properties and performance qualities of concrete and reinforced concrete structures.

11.jpg
Ayrıntılar
Beton duvarda gölge

Installation of test piece and cage on the machine.

Once the test is completed, the spacers are put back in place and the specimen and cage assembly removed from. Specimens after testing still equipped with the extensometric cage

2.jpg
Ayrıntılar
Beton duvarda gölge

Reinforcement with Composite Material

Reinforcement of concrete with composite materials. Composite materials are used to strengthen concrete for both shear and flexure. This method is aimed at improving the mechanical behavior of concrete elements.

4.jpg
Ayrıntılar
Beton duvarda gölge

STRENGTH OF CONCRETE

TO ANALYSE THE COMPRESSION STRENGTH OF CONCRETE BY PARTIAL REPLACEMENT OF CEMENT WITH FLY ASH.

6.jpg
Ayrıntılar
Beton duvarda gölge

Concrete Compression Testing

A lightweight/low-strength (~80 pounds per cubic foot) concrete test cylinder under compression testing. An linearly increasing load is being applied by the top and bottom plates of the machine, at the time of the photo the applied load was around 25,000 lbs. The devices attached to the cylinder measure the contraction of length of the sample in the direction of load. The rust colored material is a sulfur cap used to ensure flat ends.

 

8.jpg
Ayrıntılar
Beton duvarda gölge

Specimens during the compression test

Concrete pipe test values ​​verify the minimum pressure values ​​of the pipe. In the negative air pressure method test, both ends of the pipe are blocked and the air inside is pressurized to -3.5 psig (pounds per square inch).

 

10.jpg
Ayrıntılar
Beton duvarda gölge

Chemical additive for concrete,

thanks to superplasticizers, you can use up to 30% less water and up to 10-15% less cement without changing the grade strength of concrete.

12.jpg
Ayrıntılar
concrete pipe_edited.jpg
01_edited.jpg

Cumhuriyet Mahallesi, Ali Osman Çelebi Blv. No: 105, 59850 Çorlu/Tekirdağ, Türkiye

+90 (282) 652 89 42

+90 544 468 75 49

bottom of page